How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security system that protects your car from hacking and key cloning. It works by stopping the engine from running until a PIN code is entered. This could be as long as 20 characters.
This extra layer of protection is not visible to thieves who might not be aware of it. Some systems also have an application that lets owners disarm the immobiliser in case they forget their PIN or to use the service/valet mode.
Connecting the vehicle's CAN Bus
The Ghost 2 Immobiliser is an innovative security system that is able to be integrated into your vehicle's ECU, providing a discreet security line against thieves. It is extremely efficient and user-friendly and can be a valuable addition to your vehicle's security arsenal. But, as with any other anti-theft device, it's not 100% reliable and requires regular maintenance to ensure proper operation. Fortunately, this guide can help you get the most value from your Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial networking system that lets microcontrollers communicate with each over short distances. Central control units is not required. It is designed to allow multiplexing of electrical wiring in vehicles to save on copper and has a number of advantages, including low cost and a simple use.
In most modern cars, the CAN protocol is used to communicate with a variety of systems, such as the engine management system (EMS), steering module, transmission controller, air conditioning controls and many more. It also carries sensor data like speed sensors and inputs to control various features of the vehicle. The CAN bus is used to monitor these different components, and it can stop a vehicle from starting if they are in an unsafe state.
It's crucial to understand how the CAN bus works and how it's secured. It's possible to add new features to a vehicle using CAN bus, but it is important to protect it from threats from hackers and other types. Installing a firewall and monitoring your CAN-bus with software is the best method to accomplish this.
Ghost2's discrete control unit is hidden within the dashboard of the car or in the wiring harness, preventing an intruder from physically altering it. It is also impossible to reset the PIN or emergency code without access to the vehicle.
You can activate Transport Mode If you need to give your vehicle away for valet parking, service or any other reason. This feature disables the Ghost immobiliser's keyfob and ignition functions, and will only reactivate when the vehicle reaches 31 mph for 15 minutes.
Making PIN codes
The Ghost immobiliser is a powerful security device that shields your vehicle from theft. The innovative technology uses the PIN to shut down the vehicle's engine and prevent it from starting without the right code, or a valid fob/mobile. The system's sleek design makes it unnoticeable, and also provides unbeatable protection against theft. Furthermore the system is TASSA verified and can provide significant savings on car insurance premiums.
During installation when you install the Ghost system goes into the learning mode to record the sequence of buttons pressed to create your unique pin code. Once the pin code has been created and the installer has completed its work, it will guide you through the steps to activate the system. Once activated, the Ghost system will disable the motor that starts your vehicle unless you enter a valid PIN or switch the vehicle to transport mode. This makes it difficult for thieves or cloners who want to hack or clone your vehicle's starter system.
Installing a Ghost immobiliser is simple however it is essential to follow the precise instructions in the user manual to ensure proper operation. Basic hand tools can assist in making the perfect connections and a multimeter will aid in checking the electrical value. Insulation tape and heat shrink tubing are a great way to protect exposed wiring and cable ties are essential for keeping everything tidy and secure. Test the system on a regularly to spot any potential problems.
After the installation is completed, it is important to perform a final check of the system prior to switching on the ignition of your vehicle. Ghost immobilisers will re-arm themselves after 3 to 30 second, dependent on the model of your car. The system is also equipped with a Service/Valet mode that allows you to temporarily remove the system for servicing or valet parking.
Idealy, the immobiliser will be hidden under the dashboard or the steering wheel. It is recommended to use a small amount of paint or duct tape to mark the CAN H and L wires so that you can easily identify the wires during testing. The CAN H and the L wires should be connected to an electrical source that provides a constant 12V. It is essential to test the connections after testing because an incorrect identification of these wires could cause the system malfunction.
The system must be activated
A ghost immobiliser stops your car from starting unless you press a series of buttons inside the car typically the steering wheel, door panel or central console. The sequence is decided by the user and is able to be changed as needed. Once the system is activated it cannot be deactivated by thieves and is a great option for anyone who wishes to secure their vehicle from theft.
ghost immobiliser 2 is designed to be undetectable. This means it cannot be detected by modern diagnostics or code-grabbing technology. It doesn't emit radio frequencies either making it even more difficult for thieves to find.
If the device is discovered, it will stop the engine from running. It will also sound an alarm to scare the thief away. The device can be used to track a car's location and aid in the search for the vehicle in the event that it has been taken.
Contact Car Specalist Customs for a estimate or to discuss your options in a Ghost immobiliser. We are fully qualified to install a ghost immobiliser on your vehicle, and will make sure that it is tucked away in a hard-to-reach area. We can also install other security measures, including a kill switch and wheel lock to protect your vehicle from thieves.
Disarming the system
If you have an Ghost immobiliser that is fitted to your vehicle, it's essential to know how to disable it. This will aid you in the case that you lock your keys inside the car or if your battery goes out of. The system uses an unique PIN code that only you know. It cannot start the car without this code. Pressing a combination button on the steering wheel or dashboard is the easiest method of entering your code. This is a lot easier than using a key fob, and prevents others from copying the remote.
Unlike some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and works with your vehicle's CAN bus network to operate. Its main feature is its ability to bypass the engine without affecting the normal functions, making it difficult for thieves to use signal boosters to clone your car key. It doesn't emit radio frequencies, which means thieves are unable to detect it.
The Ghost system also comes with an option called Transport Mode, which allows you to temporarily disable the security system for circumstances like transportation or servicing. This feature is useful if you are lending your vehicle to someone else, without sharing your PIN number, or if your vehicle requires to be secured even while you drive it. To activate Transport Mode you need to press the service button five times within a period of 2 seconds. The Ghost system will confirm activation with five indication signals.
After you're done, make sure to save the emergency code in a secure place away from your vehicle. In the event that you find yourself locked out of your vehicle, you'll be able to contact the technician or company who installed the system and they'll give you the code. If you cannot reach them, you can always try to contact an authorized dealer however this will require verification procedures and may incur additional charges.
This system is not only useful, but it will also help protect your vehicle from theft and lower insurance costs. Many insurance companies offer lower rates or financial incentives to install this system to prevent theft.