Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is a cutting-edge anti-theft device that makes use of advanced technology to prevent car theft. The device is hidden by thieves and only turns on the engine after a PIN or app is entered.
It is weatherproof and connects to the CAN data network of your vehicle. It comes with a service/valet feature that lets you temporarily start your vehicle while it is in garage.
Easy to install
The Ghost immobiliser protects your car from theft of keys, cloning and hacking. It uses a unique PIN code system that is integrated into the car's ECU which makes it extremely difficult for thieves to identify or tamper with. Unlike traditional immobilisers, it doesn't require special keys or sensors and is completely hidden from view with no LED indications or signals that signal its presence. It's also cheaper than replacing an ECU, or installing a key fob. It can even lower the cost of insurance.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's instructions carefully. This will ensure the device works correctly and effectively. After the installation is complete, test the system by entering the PIN code, then turning on the engine. Regular testing will allow you to identify any issues before they get worse.
Check the location of the CAN H and L wires prior to beginning the installation. These are crucial to powering the immobiliser, so it is essential that they are properly connected. Labelling the wires can aid in locating them during installation. Once you have identified the location of these wires and connected them to a constant 12V power source and a grounding point. Make sure you utilize a fuse tap if necessary to protect the connections from short circuits or damage.
After connecting the wires, tidy the wiring with cable ties to avoid potential interference. It is also recommended to cover the connections with insulation tape or heat shrink tubing. This will help protect them from electrical shorts, and will increase the life of the device. It's a good idea to test your Ghost 2 immobiliser once the wiring is secure.
The Ghost 2 immobiliser offers a service mode for situations in which you may have to sell your vehicle, such as when it is being serviced or parked by a valet. This will disable the PIN sequence temporarily. Press the brake pedal, and hold the accelerator down for a number of times equal to the first digit in the emergency code. The system will then enter service mode. This can be confirmed by flashing 5 times the indicator signal.
Easy to change PIN codes
It is easy to protect your vehicle from theft using the ghost 2 immobiliser. It is hidden inside the vehicle and can only be accessed using a specific code. The device connects directly to the vehicle ECU through its data bus. It does not use radio frequency signals as do traditional Thatcham immobilisers or other aftermarket alarm systems. This makes it more difficult for thieves to hear the click of an immobiliser relay, or add new keys. The control unit is hidden in the wiring of the vehicle or dashboard, and cannot be physically altered to reset the system.
The ghost 2 immobiliser connects to your vehicles CAN Data network and utilizes existing buttons on the steering wheel, door panels, and the centre console to create an individual sequence of up to 20 button presses which must be entered prior to the engine starts similar to a PIN code. This unique next generation system does not require cutting of wires when it is installed and can be fully reprogrammed at anytime. You can even start your vehicle in Service or Valet mode after you hand it to a mechanic do work.
The application can also be used to disable your PIN number if you've lost your keys or change it. This feature is especially helpful in the event that you have offered your vehicle to someone else for valet parking or servicing, as it stops them from starting your vehicle and taking it away without permission. It's also inaccessible to professional thieves because it doesn't make use of circuit cuts or radio frequencies.
Another great feature of the ghost 2 immobiliser is its capability to stop relay thefts. Relay theft is a popular method of car theft where the criminals attack the diagnostic port of your car, then modify the signal sent by the key to the vehicle's ECU in order to fool it into believing that a valid key is present. The traditional immobiliser can be manipulated in this manner, however with the ghost 2 immobiliser, the signal is blocked by the immobiliser prior to it reaches the ECU.
Simple to use app
Ghost 2 is a revolutionary immobiliser that safeguards your car from key-cloning, hacking, and key theft. It connects to the CAN data network of your vehicle and requires the use of a PIN number to start the engine. It also stops thieves from using signal spoofing and device spoofing, which are both common techniques used to steal vehicles.
The system is easy to use and operates similar to a standard car alarm. Installing the system will allow you to create an individual 20-digit PIN code that must be entered before you start the vehicle. This will prevent the vehicle from being taken even if your keys get removed. ghost autowatch immobiliser can turn off the system using an app on your smartphone.
The ghost is silent and does not emit radio frequency signals. It is a quiet, weatherproof device that can be placed anywhere inside your car. It can be hidden in the dashboard, behind the steering wheel or door panels. It communicates with your ECU over the CAN data circuit and is not affected by diagnostic tools, which some thieves use to identify security systems. It is also not affected by jamming devices that alter codes.
It is a hidden installation that doesn't require any wire cutting or modifications to the vehicle and can be utilized as an anti-theft system for all vehicles. The technology has been proven efficient, and it's in compliance with TASSA Standards. Ghost is a great solution for classic, sports and prestige cars, and it can also be used to secure vehicles that are hired out through apps such as Turo.
The Autowatch Ghost 2 represents the next generation of vehicle immobilisers. This system is invisible to thieves and stops the vehicle from starting without your PIN, or unless they are authorized by the app. It also doesn't emit radio frequencies or other signals that can be detected by scanners. The installation process is easy and quick. The app is easy to navigate and offers a user-friendly interface that makes it simple to install and use. It also includes an GPS tracker that can assist police find the vehicle and locate it.
Simple to reset
Ghost 2 immobilisers are an excellent method to guard your vehicle from theft. It integrates into your vehicle's ECU, creating a barrier that thieves can't break through without the proper pin. The device is TASSA certified that means it's recognized by insurance companies. It's a useful tool to deter theft of your car and could save you money in the end.
The Ghost system unlike traditional alarms and immobilisers that require cutting of circuits and is directly connected to your vehicle's CAN data network. It works by pressing the buttons on your dashboard and steering wheel. You can set up an individual PIN sequence that is up to 20 presses long. This PIN must be entered before the engine can start, just like a credit card. The Ghost system is completely inaccessible to thieves and has no LEDs to indicate its presence. This makes it the most effective aftermarket CAN-bus immobiliser available today.
The Ghost system has another advantage that it does not transmit radio frequency signals. ghost autowatch immobiliser means it cannot be scanned by thieves or intercepted. This prevents cloned key attacks and relay attacks as and the typical method of hacking into a car's computer system using its CAN bus by searching for signals. The Ghost system is designed in a way that it can be hidden inside your vehicle. There are no LEDs, or other signals to signal its presence.
The system features the option of a Transport Mode which disables the Ghost System. This is beneficial in situations where you may need to temporarily deactivate Ghost for instance, when transporting or servicing your vehicle. This mode is less effective than Service Mode as it doesn't deactivate the Ghost system if you exceed 31 mph within 15 minutes.
To reset your ghost 2 immobiliser you'll need the emergency code, which you can obtain from your installer. It is typically hidden beneath a scratch-off area on the card supplied with the installation. This emergency code should be secured and stored in a secure place, such as a wallet at home.